8/04/2010

Review of Convenient Cordless Soldering Iron for Professionals and DIYers - Features with a LED at Tip!

I bought this at Radio Shack thinking it would just be something I would use once then throw away. I desperately needed a way to wire in the remote start in my truck.I still have it and use it fairly often. For being so cheap it works great. I have had it for over a year and 1/2 and am only on the second set of batteries. I can't believe how long they last. It has a small light to illuminate what you are working on not super bright, but better than nothing. The time it takes to go from cold to hot is really quick, about 5 seconds. It has an actual metal tip unlike the ceramic "cold heat" that I bought a while back. (My cold heat now lives in the garbage).
Overall it is much more useful than I expected. Since it is battery powered, it wouldn't make sense as a primary soldering iron. But for those times you want portability, it defiantly exceeds expectations.

Click Here to see more reviews about: Convenient Cordless Soldering Iron for Professionals and DIYers - Features with a LED at Tip!

Product Description:
This cordless soldering iron provides you with the soldering ability of a 15W soldering iron without the restrictions of having to be tied down by the cords. Instantle reaching 365 Fahrenheit and with a maximum temperature of 1050Fahrenheit, this soldering iron only uses 4 AA batteries so it produces a lot of heat with little power.

Buy Now

7/25/2010

Review of Hobart 300143 Welding Hobart Welding 3035-20-Feet Spool Gun

great tool, easy to hook up, very simple if you cant do it or struggel at it you should not be out of the house without some one to watch you. It welds very good, it h as good controll for speed and power, you have to play around to weld thiner stuff untill your used to it but it will do the job great.

Click Here to see more reviews about: Hobart 300143 Welding Hobart Welding 3035-20-Feet Spool Gun

Product Description:
Includes spool gun and 20ft. cable. No module required for hookup to IronMan welders. Fits Item# 1646955. U.S.A. Works With: IronMan 210 MIG Welder, Cable Length (ft.): 20

Buy Now

7/15/2010

Review of CUTTING TIP FOR SOLDERING GUN

In my city of 25 thousand and neighboring area, not one of 6 hardware stores had this very needed item. Thanksd to Amazon I found these and amgreatful.

Click Here to see more reviews about: CUTTING TIP FOR SOLDERING GUN

Product Description:
Replacement Tips - SolderingType: ScrewdriverFor Use With: 8200/D550/D650For Use With: D550/8200Point Size: 0.340 In.Tip Series: CHTip Diameter: 11/32

Buy Now

7/05/2010

Review of Wahl 7800 CORDLESS SOLDERING IRON KIT

I've been in the electronics business for years, and I've always had two of these irons sitting on my bench -- one in use and one charging.It fits your hand perfectly, travels well with a locking button, lights up your work and has a very large assortment of tips to choose from (from broad to very, very fine), all easily changeable without any tools.

I finally had to buy a new one after many years of use out of the old ones, I'd say at least 15 years.

For production work I recommend a corded high-end workstation, but for repairs this iron can't be beat.

There are a few times when I have to get out the big Weller gun, but the Wahl does the job 95 percent of the time.

Click Here to see more reviews about: Wahl 7800 CORDLESS SOLDERING IRON KIT

Product Description:
ISO-TIP 60 CORDLESS SOLDERING IRON, CONTAINS: IRON, CHARGING STAND WITH PLUG TRANSFORMER, BATTERY #21-4528, CHISEL TIP #21-4545,

Buy Now

6/25/2010

Review of Wahl 7700 CORDLESS SOLDERING IRON KIT QUICK CHARGE

The Wahl 7700 Iso-Tip soldering iron works perfectlyAlmost instant heat, and it holds its charge for a long time.

Click Here to see more reviews about: Wahl 7700 CORDLESS SOLDERING IRON KIT QUICK CHARGE

Product Description:
ISO-TIP CORDLESS SOLDERING IRON KIT, SOLDERING HEAT TIME : (AVG) 5~10 SEC, CONTAINS: CORDLESS SOLDERING IRON, RECHARGING STAND, T

Buy Now

6/15/2010

Review of Weller 7135W Replacement Soldering Gun Tip

These tips work great.As long as I do not drop the soldering gun or use the tip to pry wires apart, they last forever.

Click Here to see more reviews about: Weller 7135W Replacement Soldering Gun Tip

Product Description:

Fits Tool(s): 8200, 9200
Tip Style: Standard
Tip Width O/D: .165 in./4.19 mm
Reach/Length: .885 in./22.48 mm




Buy Now

5/12/2010

Review of Weller P2C Portasol Professional Self-Igniting Cordless Butane Solder Iron

For anyone who owned or used the original Portasol soldering iron, they will notice some vast improvements to this second design. Primarily, ignition no longer requires a "bic-lighter-type-spark" (that usually required at least three efforts), as it has been replaced by a piezo-electric spark. In addition, the gas supply seems much more stable and controllable,and finally, the soldering tips are much more robust and use the same mounting device for easy switching (though one must still wait for those parts to cool down before handling). Overall, the tool is well-built and very quick to achieve soldering temperatures. The only negatives I see are the relatively short run-time per tank of gas (about 45 mins on a low setting - less than they claim), and the absence of a temperature gauge, or series of led lights to roughly indicate temp. I don't think this feature is present on other, even more expensive portable units, but it would be a nice addition to ensure that expensive electronic components (esp high power LEDs) don't get fried.

Click Here to see more reviews about: Weller P2C Portasol Professional Self-Igniting Cordless Butane Solder Iron

Product Description:
Lightweight, Cordless Butane Soldering & Hot-air Tool Esd Safe To Protect Sensitive ComponentsFast Heat-up For High Productivity?melts Solder In Less Than 40 SecondsGas Capacity Allows Up To 1 Hour Of Continuous Use Refills In Less Than 20 SecondsAutomatic Cut-off Switch When Cap Is Replaced For Safety

Buy Now

5/11/2010

Review of Dremel 290-01 1.15 Amp 7,200 Stroke Per Minute Engraver includes Letter and Number Template

I bought this engraver with birthday money from a discount store last fall, after researching it online.It will leave its mark on just about anything you would want. I like the variable speed settings which allows you to match the work to the material. I have used it to initial all my tools so there is no mistaking who it belongs to. It works on hardened steel as well as plastic. My wife uses it for craft projects in her pre-school teaching job.

Click Here to see more reviews about: Dremel 290-01 1.15 Amp 7,200 Stroke Per Minute Engraver includes Letter and Number Template

Product Description:
Engrave, decorate, or personalize a wide variety of materials--from metal to plastic to wood and leather--with the Dremel 290-01 7,200 Stroke Per Minute Engraver. This handy tool includes a letter and number template for infinite artistic possibilities. It also features a soft-grip body, replaceable carbide engraving point, and variable stroke control.
The Dremel 290-01 7,200 Stroke Per Minute Engraver includes:
  • Engraver tool
  • Letter and number template
  • 9924 carbide point


The included letter and number template makes it easy to personalize your items.View larger.

With a five-position stroke adjustment, the engraver etches fine lines and deep grooves.View larger.

The included 9924 carbide engraving point ensures precise results.View larger.7,200 SPM Motor for Powerful Performance with a Variety of Materials
Powered by a 7,200 SPM, 115-volt motor for reliable performance, the 290-01 lets you personalize your valuables or decorate metal, glass, and stone for a unique touch. It's also perfect for ceramics, crafts, and jewelry making.
Unlimited Personalization and Decorative Options
With the 290-01, the only limit is your imagination. Engrave your wedding date on a glass tumbler for a special anniversary gift or wedding favor, jazz up a plain wooden frame with a mix of lines and letters, or embellish a simple mirror with a lovely engraved design. With this tool you can also mark your valuables to help protect them from theft and engrave your name directly on your luggage to make it easier to spot your bag at the airport.
Engrave for Protection Against Theft
The Dremel Engraver helps you identify and protect property like tools, bikes, cameras, TVs, and other valuables quickly and easily. Engraving your valuables with your name or identification number makes them less likely to be stolen, as personalized items are more difficult for would-be thieves to sell for a quick profit. Plus, should your property become lost or stolen, having identification on the item helps police return recovered items to you more quickly.
Five-Position Stroke Adjustment for Precise Results
Featuring a five-position calibrated stroke adjustment dial to regulate the engraving depth, the 290-01 lets you etch fine lines or deep grooves in metal, glass, wood, leather, plastic, and ceramic. Its soft-grip body ensures a comfortable, secure grip, while a replaceable carbide engraving point ensures precise results. For added versatility, you can also purchase an optional 9929 diamond point (not included) for heavy-duty use on hard surfaces.
Compact, Lightweight Design for Easy Handling and Comfortable Grip
Weighing just 12 ounces, the 290-01 has a light and compact design that lets you perform intricate work without excessive stress on your wrist or hand, and the included number and letter template helps you complete your engraving quickly and easily without mistakes.
For additional peace of mind, the 290-01 comes with a two-year warranty.
About Dremel: A History of Brilliance and Innovation
Founded in 1932 in Racine, Wisconsin, Dremel is the industry leader in rotary tools. The company owes its success to the inventive genius of its founder and namesake, Albert J. Dremel. In his lifetime, Mr. Dremel owned 55 patents on a wide range of products from electric erasers to a gas-powered rotary lawn mower. His most famous and important invention was a high-speed rotary tool, dubbed the Dremel Moto-Tool. Compact, lightweight, and perfect for a wide range of jobs, the rotary tool was an immediate hit with hobbyists and eventually became accepted as one of the greatest inventions of the 20th century. Today, the Dremel name remains synonymous with utility, durability, and innovation.
What's in the Box
Engraver tool, letter and number template, and 9924 carbide point
The versatile, easy-grip 290-01 lets you decorate and label a wide range of material, from tough metal to delicate glass.



Buy Now

5/10/2010

Review of Micro Pencil Butane Torch Lighter

theres no spark n the on and off valve are finicky,fluid goes fast.could be smaller upping its portability

Click Here to see more reviews about: Micro Pencil Butane Torch Lighter

Product Description:
The size of a pencil with full-size power! This micro pencil torch is great for any electrical work, building fires, fixing any metals, and various household needs. The compact design of this 9" blue flame breather is perfect for tool box or utility drawer. A great tool to always have around.

Buy Now

5/09/2010

Review of PROFESSIONAL 30W SOLDER IRON CUSHION GRIP

Very even heating.Supplied tip is OK but for micro work, buy the fine pointed tip at the same time instead of paying for s/h twice or having to wait for the second delivery.An addt'l recommendation would be to purchase a stand if you don't already have one.

Click Here to see more reviews about: PROFESSIONAL 30W SOLDER IRON CUSHION GRIP

Product Description:
Cooper Hand Tools, a division of Cooper Industries, Inc., manufactures and markets many well-known brands of hand tools, chain, and electronic soldering products, including Campbell chain, Crescent brand wrenches and pliers, Lufkin measuring tools, Nicholson files and saws, Plumb hammers, H.K. Porter bolt cutters, Weller soldering products, and Wiss snips. Headquartered in Raleigh, North Carolina, Cooper Hand Tools has manufacturing facilities in 16 international locations, and has approximately 4,400 employees worldwide.

Buy Now

5/08/2010

Review of Bernzomatic Corp Micro Torch Kit W/tips

First off, it's advertised as having "6-tips-in-1", but in my opinion it only really comes with 4 tips.There is an integral tip to be used for hot blower applications (like heat shrinking), so I guess you could count that as a tip.The other 4 tips screw into this one.The tip advertised as being useful for soldering copper pipes is with no attachments or tips installed - just the naked torch.

I seriously doubt that this puts out enough heat to actually solder a copper pipe any larger then 3/8", or the copper tubing used for ice makers.

And in general, the flame is not that uniform and flame control is not that precise.You'd be better off buying a more expensive torch and save yourself the frustration from using this one.

Click Here to see more reviews about: Bernzomatic Corp Micro Torch Kit W/tips

Product Description:
For precision light soldering, polyfoam cutting and heating, craft and hobby projects, electronic repairs, and small household projects. Refillable, uses butane fuel. Includes soldering tips, hot knife tip, polyfoam cutter and torch stand. 3,100 degrees F

Buy Now

5/07/2010

Review of Dremel 290-05 120-Volt Industrial Engraver

great little unit! works on all metals including saw blades and router bits. I am using the diamond tip with it. powerfull and not too loud. glad i own it.

Click Here to see more reviews about: Dremel 290-05 120-Volt Industrial Engraver

Product Description:
Stroke adjustment dial regulates engraving depth from fine lines to deep grooves;Replaceable carbide point lets you engrave on most surfaces;Letter/Number template helps etch words and numbers;Soft grip adds extra comfort and control;Light and compact design provides comfortable use for precision engraving performance;Two year warranty

Buy Now

5/06/2010

Review of Butane Micro Torch

The torch looks and performs exactly as described.After very limited use (about 6 months of casual kitchen use), the automatic ignition system failed and it would no longer light.We continued to use it for a while by lighting it with a lighter, but after about 6 months, we threw it away.We didn't get our money's worth.

Click Here to see more reviews about: Butane Micro Torch

Product Description:
Butane Micro Torch For Electrical Repair & Soldering. This is a new butane micro torch. This micro torch has an electronic instant ignition system for push button start ups. This can be used on jewelry, automotive, electronics, outdoors, emergency kits, first aid kits, hobbies, home plumbing, waxing skis and in dental labs. Provides up to 120 minutes of burn time. It has a high temperature flame of 2370 degrees F (1298.8 degrees C). Butane not included. It measures approximately 6" (152 mm) long.

Buy Now

5/05/2010

Review of Hakko Desoldering Kit, With 808 Gun, 120 VAC

I have used tons of solder suckers, and for the past 15 years, a Pace MBT-200 soldering/desoldering station.The Pace worked for a lot of years but always needed a lot of maintenance.It was ok but I always had a feeling there must be something better.It was what my boss bought so I was grateful just to have one.I've been having a hard time finding tips lately, so I decided to look for a station for myself.After reading a ton of reviews I bought this Hakko 808 and I got to say, i must've been living in a closet.This thing is absolutely the best.I have it on the temp setting from the factory which is kinda midway and with the tip that it came with and it cleaned up all the mess of a board that the pace couldn't handle.nice clean holes.I guess there could be better, but this is best in class for me.a bonus is, it's portable.I would definitely take it out in the field.It is kinda expensive at $159(free shipping from amazon) just for a desolderer.but, i just did 10 holes in one pass in like 30 seconds.definitely a lifestyle changer, a stress reliever.nah, but i really do enjoy using it.i hate to say it sucks, but it sucks good!if you're like i was and can't make up your mind btwn the cheap one at that other site and the Hakko 808 at amazon.don't eat lunch for a month and buy the Hakko!!

it's been over a year now, and it still works great!

Click Here to see more reviews about: Hakko Desoldering Kit, With 808 Gun, 120 VAC

Product Description:
Hakko 808 Desoldering Gun - The Hakko 808 Kit is a handy, portable desoldering tool with a built-in vacuum pump. No separate station is required. The unique design places the pump and motor above the grip. Delicate tasks are performed with greater ease; the tool can be used for long periods without operator fatigue. Pump maintenance is quick and easy - simply remove the cover. Adjustable temperature control (380-480°C/715-895°F). Kit includes: desoldering tool, solder tip, solder sock and case.

Buy Now

5/04/2010

Review of Wall Lenk L96E Engraving Tool 120 VAC

Product is very handy for small detail work on metal.I use it to detail and sign my hand-crafted silver and base metal jewelry.


Click Here to see more reviews about: Wall Lenk L96E Engraving Tool 120 VAC



Buy Now

5/03/2010

Review of Classic Easy-to-Use 60-Watt Pencil-Style Soldering Iron

it is a nice solder, if you intend to use it much buy more tips, as the tips tend to wear out quite quickly

Click Here to see more reviews about: Classic Easy-to-Use 60-Watt Pencil-Style Soldering Iron

Product Description:
Excellent choice for precision work on electronics, jewelry, silver smithing, arts and crafts. Dimensions: length overall 8-1/2", element and tip 4-1/2", weight 4.7 oz including power cord.

Buy Now

5/02/2010

Review of Weller Pro Series Battery Powered Soldering Iron

These do work, if only just.They are suitable for occasional light soldering jobs involving a small number of narrow guage wires, component leads and/or circuit board traces.Large wires, terminals or power/ground plane vias without thermal relief will draw away too much heat for the solder to melt.It doesn't help that the new tin/silver/copper alloy solders have a higher melting point and don't flow as well as tin/lead.If you need to solder heavier things, forget battery powered and get a corded soldering gun or iron.If you need to do a more than a small number of connections on circuit boards or are going to use it often, it would be better to invest in a controlled temperature soldering station.

Instead of using Alkaline batteries as the manufacturer recommends, I'd suggest NiMH rechargables with a fresh charge at the beginning of every job.Not only will it be cheaper to run, but I believe the NiMH cells have a higher sustained current output capacity which is what this kind of application demands.

Click Here to see more reviews about: Weller Pro Series Battery Powered Soldering Iron

Product Description:
Heats Up To Working Temperature In Under 15 SecondsWhite Led Light Illuminates Working Surface Red & Green Leds Indicate Whether Power Is High Or Low Protective Safety Cap Turns Off Power When Placed On Tool Ideal For Field Service Repair On Small Parts & ComponentsIncludes Iron, Safety Cap, 4 Aa Batteries, Lead-free Solder & Tip Wrench

Buy Now

5/01/2010

Review of Cooper Tools WP25 Weller

Weller has been the gold standard for ever! This TEMP CONTROLLED iron will run forever. The tip provided is way to big for printed circuit work, so order the smaller tip right away and you will increase the usefulness of this iron a whole bunch. Enjoy!

Click Here to see more reviews about: Cooper Tools WP25 Weller

Product Description:
Perfect for a variety of electronic soldering work, this top quality iron features a long life, double coated tip and a quick change, plug-in heater element. Lightweight handle includes a comfortable cushioned grip. Net weight: 1/2 lb.

Buy Now

4/30/2010

Review of Cooper Tools GT7A3 Solid State Soldering Guns, Operating Temp.: 600 F or 700 F

Had one of these guns before and have always liked it. Like the conical tip better as it suits most of my soldering jobs better, but this beats the hell out of most irons if you need more heat!

Click Here to see more reviews about: Cooper Tools GT7A3 Solid State Soldering Guns, Operating Temp.: 600 F or 700 F

Product Description:
Cooper Tools GT7A3 Solid State Soldering Guns, Operating Temp.: 600 F or 700 F

Buy Now

4/29/2010

Review of Master Appliance UT-100SIEA Cordless Butane Flameless Soldering Iron / Heat Gun with Fan

If you need a cordless heat gun this unit to get. It is very well made and does the job. I do a lot of specialty wiring and use heat shrink tubing often, the Master Appliance flam-less heat gun offers a focused burst of heat to do the job. Once more, the fan option gives a turbo boost to your work area as heat is available whether the fan is one or off. I'm confused why they call it a soldering iron though.

Click Here to see more reviews about: Master Appliance UT-100SIEA Cordless Butane Flameless Soldering Iron / Heat Gun with Fan

Product Description:
butane-powered flameless heat tool with fan assisted air flow. Ideal for terminating shrink tubing and specialty connectors 10mm I.D. or less.

Buy Now

4/28/2010

Review of Aoyue 701A+ Dual Function Soldering and Desoldering Station

I bought the 701 for a home/hobby project that required quite some de-soldering. First impressions of the Ayoue:
-Solid build
-Well packed
-Comes with replacement tips, filters etc.

Initial dislikes:
-A scratch on case
-Missing trimmer cap
-User manual could improve

It looks like Ayoue lacks a little with their quality control. However working with the 701 is fun:
-De-soldering works great
-Nice feel (handling) of the de-soldering gun
-Gun is easy to use (compared to Weller foot pedal)

Dislikes during use:
-Iron holder a little cumbersome (holder for pump-gun is OK)
-Iron handle gets warm (compared to Weller)
-Tossing pumped solder is difficult
-Solder reservoir is too small

All in all, at that price, the Ayoue is unbeatable. If you are on a budget and need a de-soldering station, the 701 is the way to go. I would buy it again.




Click Here to see more reviews about: Aoyue 701A+ Dual Function Soldering and Desoldering Station

Product Description:
This is a Dual Function soldering and desoldering station for thru hole boards and components. The tools has zero crossing circuitry to prevent electrical surges. The soldering iron has a ceramic heater for longer service life.Features:Long Life heat Elementsolder iron and desolding tool are independent35 watt solder iron24 volt output to prevent circuit damage from the ironTemperature range 200-480 C (392-896 F)Suction Flow 15 L/min (max)Package content:701 Station,B1001 Desoldering gun, Desoldering tips (S, M, L), 201412 Desoldering gun holder, B001 Soldering iron,2630 Soldering iron holder, 201242 Nozzle cleaning pin, 3017J Filter (6 pieces), H022 Silicone Grease,20125 Filter spring, Power cord.

Buy Now

4/27/2010

Review of Aoyue 8032A++ Hand Held Digital Hot Air rework Gun

Nozzles are available cheaply from the same manufacturer.I recommend using the quartz PCB preheater as hot air in general is a bit slow (compared to regular soldering iron), and that can be found on the web for a bit over a hundred dollars.

Click Here to see more reviews about: Aoyue 8032A++ Hand Held Digital Hot Air rework Gun

Product Description:
This Hand Held Digital Hot Air gun provide precise temperature and airflow control at your finger tips. Quickly solder and de-solder any SMT electronic components and shrink, "Heat shrink tubing".The microprocessor controlled gun utilizing a turbine air flow to generate an even stream of concentrated hot air. It is a great tool to keep in your field service bag.It has a digital readout for temperature and airflow. Features:550 watt metal heaterQuick heat up Temperature range 100-480 C (212-896 F)Turbine motor Air Flow 30L/min (max)Station Dimensions: 7.7 diameter x 277 length (mm) Package contents:8032A++ Main unit, Air nozzles (1195, 1196, 1198, 1313)

Buy Now

4/26/2010

Review of Cooper Tools GT7A Solid State Soldering Guns, Operating Temp.: 600 F or 700 F

I have owned this since the early 1970s. This gun is ideal for many electronics soldering applications. It is very light weight but heats up quickly. It provides more than enough heat to, for example, solder Amateur Radio antenna connectors. Also great for repairing hand wired circuitry in older radios and automotive soldering.

Because it is temperature controlled it is easy to prevent burning items with too much heat, as is possible with normal soldering irons. This really benefits the quality of the finished product soldered connections. I hesitate to say that this gun makes soldering easy, soldering is an art. But it does make soldering easier.

Be careful, when you are not actively soldering let go of the trigger. If the gun is not actively touching some metal to act as a heat sink it will turn itself up to full temperature and burn out the tip prematurely. Until I discovered this I replaced a few tips. Now they seem to last forever. The tips cost about half of the total price for the entire product. Let go of the trigger when you are not soldering, it will heat back up very quickly when you are ready to solder.

These do cost more than run of the mill guns but there is a reason. This gun is in a class of its own.

Click Here to see more reviews about: Cooper Tools GT7A Solid State Soldering Guns, Operating Temp.: 600 F or 700 F

Product Description:
Cooper Tools GT7A Solid State Soldering Guns, Operating Temp.: 600 F or 700 F

Buy Now

4/25/2010

Review of Weller 80 Watt Soldering Iron

This is a good, general purpose iron. It is well suited for light to medium work. I purchased it for this reason.

Click Here to see more reviews about: Weller 80 Watt Soldering Iron

Product Description:
Type: Non-temperature Controlled
Wattage: 80 W
Temperature Range: 900° F
Cord Length: 6 ft.

Buy Now

4/24/2010

Review of Weller TB5TK Replacement Tip Kit for TB100PK

decent product for what it is ,but did not get as hot as I wanted it to.I had a tough time melting the plastic I needed to melt.a pencil iron with a home made copper tip worked better.

Click Here to see more reviews about: Weller TB5TK Replacement Tip Kit for TB100PK



Buy Now

4/23/2010

Review of Ungar 1095 Dual Temperature Heat Gun

I bought this unit about six years ago, and used it a few times a month for light-duty electronics work. It simply stopped working one day. It just blew warmish air instead of hot air. Do yourself a favor. Buy something else.

Click Here to see more reviews about: Ungar 1095 Dual Temperature Heat Gun

Product Description:
Item #: 185-1095. Dual temperature heat gun, ideal for most heat gun applications
Cures epoxy and loosens adhesives
Drying, thawing frozen pipes
3-way switch...Hi-Off-Low
3-wire grounded plug 6' power cord
  • Operating Temp. = 790 øF [Min], 1200 øF [Max]
  • Voltage = 120.00 VAC
  • Watts = 1000.00 W
  • Fan Cord Control Type = On/Off - 2 Temperatures
  • Handle Wt. = 22 oz
CUL listed|UL listed
Customers also search for: Tools and Storage\Power Tools\Heating Tools\Heat Guns and Torches Discount 03074 Dual Temperature Heat Gun, Buy 03074 Dual Temperature Heat Gun, Wholesale 03074 Dual Temperature Heat Gun, 037103030740, 1095, Corded Heat Guns

Buy Now

4/22/2010

Review of Aoyue 937+ Digital Soldering Station

This iron heats up very quickly and works beautifully.Comes with an extra ceramic element just in case the one you have somehow goes bad.

Click Here to see more reviews about: Aoyue 937+ Digital Soldering Station

Product Description:
This is a 45 watt digital soldering station that has a 1 degree C control.Features:ESD SafeLong Life Ceramic heat ElementDigital thermostat control ± 1 C24 volt output to prevent circuit damageTemperature lock50 watt Power consumptionTemperature range 200-480 C (392-897 F)110 V ACPackage content:937+ station, B001 Soldering iron, 2630 Soldering iron holder, C001 Soldering iron spare heating element. Solder is not included with this item

Buy Now

4/21/2010

Review of NEW SOLDERING IRON STAND HOLDER + SPONGE METAL GUN HOLD

I had been looking for a stand similar to this one for quite a while. Although I could find a reasonably priced stand, the shipping charges were always ridiculous. (One of my biggest pet peeves is spending more for shipping than the actual items costs!) When I saw this one offered for around $10 (including shipping), I pounced! Not a bad deal at all - especially when I've seen these same units for $8-$10, without shipping.

If you can tighten a nut on a bolt, you're able to put it together. Schwing! Easy assembly. This works perfectly with my fine tipped soldering iron and I can almost hear my desk thanking me every time I slide my iron into this stand (rather than trying to carefully balance it in an upside down flower pot). The coild holds the very hot part of my iron securely, so I'm not worried about it being knocked over. And even tho the unit comes with the cheapest little sponge thing I've ever seen, it DID come with a sponge. lol It is easy enough to buy a regular sponge and cut it to the desired size for tinning.

I would recommend this to anyone who wants to protect their furniture when soldering. A great little item at a very reasonable price!

A side note: I bought this from All Top Bargains and I would like to give them a shout out. They have fabulous communication and the fastest shipping I've ever seen with an Amazon store. I am really impressed with this seller and the way they handle things - so if you have the chance to buy this soldering iron stand from All Top Bargains, double bonus!!

Click Here to see more reviews about: NEW SOLDERING IRON STAND HOLDER + SPONGE METAL GUN HOLD

Product Description:
Metal stand with sponge that fits most standard soldering irons. For pencil type Irons. All metal construction.Easy to assemble. Sponge included.

Buy Now

4/20/2010

Review of SW3 Desoldering Wick

I bought this to work on a project that required removing colored LEDs from a circuit board so I can install white LEDs... so I was removing about 150 connections.

It worked OK at first... it would suck up the old solder but took some poking and prodding to get a good contact.Also, you need a hot iron so you can heat both the solder and the wick (perhaps that was the problem the other guy had???Don't try this with a cheap iron that doesn't get hot... it should be able to very quickly melt the solder)

But then I had a brainstorm... I grabbed some of my flux (the "stuff" you put on before you solder copper pipes together... look in the plumbing section of any hardware) and lightly coated the end of the wick with the flux.This makes it work 30 times better!The flux draws the solder into the wick so fast that its amazing.

Just be careful not to get too much flux on the wick, as it will get all over what you are desoldering as it gets hot.

As you are using it... once the end gets thoroughly coated with old solder just cut off that part and then touch it to the flux and then keep going.

(you might not realize it, but your solder most likely contains a flux core... thats why you don't need it to put down the new solder... but its not there for the old solder so you have to add it to the wick)

Click Here to see more reviews about: SW3 Desoldering Wick

Product Description:
Desoldering Wick

Buy Now

4/19/2010

Review of Weller WLC200 80-Watt Stained Glass Soldering Station

After a solid recommendation from "My Sister, The Professional Artist", I purchased this soldering iron for yet another reason not to do housework. The iron itself produces the steady high heat necessary for stained glass work and is perfectly complimented by it's stand.The rheostat is responsive, the cleaning pad is very handy and the wire holder is placed just where you need it.The $60 price is excellent for a tool of this quality and when needed, additional tips are readily available. Great equipment.

Click Here to see more reviews about: Weller WLC200 80-Watt Stained Glass Soldering Station

Product Description:

Wattage 5 W - 40 W
Temperature Range 900° F
Voltage Input/Output 120 V/120 V
Temperature Accuracy Not Measured



Buy Now

4/18/2010

Review of Weller SPG80L Marksman 80 Watt Stained Glass Soldering Iron

Works wonderfully for stained glass, could use a regulator to control the tempature after is has been on for a while.

Click Here to see more reviews about: Weller SPG80L Marksman 80 Watt Stained Glass Soldering Iron

Product Description:
For stained glass work; can tackle more intricate seams and repair old ones. Simple and safe to use. Stainless steel barrel with heat and impact resistant handle. Includes No.SP80 iron, soldering iron rest, 3/8" No.MTG20 and 1/4" No.MTG21 pre-tinned iron- plated copper tips that develop 900 degrees Fahrenheit. 9-3/4"L, 120 Volts, 80 watts, 50/60 Hz. U.L. Listed.

Buy Now

4/17/2010

Review of Weller SP40LK 40 Watt Soldering Iron Kit

I am not sure why others have rated this iron so poorly. I haven't had any problems using this soldering iron. This is the first one I've ever owned, and it's pretty easy to use. It heats up quickly and adequately for soldering Silver-containing solder with no problems for audio electronics. I do recommend getting a better soldering iron stand with a cleaning sponge for better safety practices and tip maintenance. The other feature I like is using other quality Weller tips which are reasonably easy to find in local hardware stores and electronics shops.

Click Here to see more reviews about: Weller SP40LK 40 Watt Soldering Iron Kit

Product Description:
Marksman 40W soldering iron kit. Model No. SP40L iron; No. MT10, ST3, and ST7 tips; lead free solder; and soldering aid tool. Indicator light allows you to see that the iron is On. Ideal for electronics, electrical, hobbies, kits, etc. Develops 900 F. tem

Buy Now

4/16/2010

Review of Black & Decker CI500S Dual-Temperature Soldering and Craft Iron

This maybe suited best for arts and crafts projects with all its different attachment tips,but if you want to solder electricalparts, forget it. The soldering tip never gets hot enough for quality work.Better to spend the extra money and get a real soldering iron that works.

Click Here to see more reviews about: Black & Decker CI500S Dual-Temperature Soldering and Craft Iron

Product Description:
The Black & Decker CI500S dual-temperature soldering and craft iron offers temperatures of either 500 or 900 degrees, making it versatile enough to use on wood, metal, wire, fabrics, ceramics, and other materials. Seven interchangeable tips -- including soldering, universal, round, teardrop, tapered, hot knife, and mini-iron -- perform a variety of tasks. On the iron, an indicator displays a red color for high temperatures and yellow for low temperatures. The soldering and craft iron kit includes a cooling stand with a storage drawer for the tips, third-hand grippers, and a sponge. Black & Decker backs its iron with a full 2-year warranty.
What's in the Box
Craft iron, seven interchangeable tips (soldering, universal, round, teardrop, tapered, hot knife, and mini-iron), cooling stand, and sponge.

Buy Now

4/15/2010

Review of Wall Lenk LSP-60 SOLDERPRO 60 2-in-1 Butane Powered Soldering Iron & Blow Torch

I can't tell for sure, but this looks a lot like a radioshack brand torch I bought a while back. It's has a nice adjustable flame that stays lit. It burns a long time too because it holds a lot of butane (for it`s size). I helped a guy put a new door on is car. Why to I need a torch for that? Well he cut all the wires in the door instead of taking them off the various devices and pulling them though the rubber conduit first (DON'T DO THAT!!! Hehehe). Anyway while he transferred all the parts I worked on the door harness. Spent nearly an hour soldering and shrink wrapping I'd say at least 35-40 wires back together. About ¾ the way through it ran out (not bad).

Features (if it is the one I think it is):
Built in wire stand, not vary ridged but works all right. Standard changeable tips, but nowhere to store them. It should come with a flam tip and a tapered round iron tip. Cap with built in flint igniter (just like a cigarette lighter), flint can be changed. Seems the best way is to take a pare of long noise pliers and pull the whole striker assembly out (takes a little force). Once you get it out you "unlatch" the spring, pull it out and the flint should drop out. You can replace with the standard ones you can buy at the drug store.

Nice little torch to have or take with you if you need to solder/heat up/melt something.

Click Here to see more reviews about: Wall Lenk LSP-60 SOLDERPRO 60 2-in-1 Butane Powered Soldering Iron & Blow Torch

Product Description:
2 in 1 cordless and portable butane soldering iron and blow torch. Equivalent to 30W to 70W electric tools. Great for electrical work, light brazing, model building, shrink tubing, thawing frozen locks, and so much more.

Buy Now

4/14/2010

Review of Variable Wattage Soldering Iron 0-50 Watts

First let me say the build quality is VERY GOOD.How very useful, . . . there is a variable heat adjustment built in giving you a choice of a low wattage iron perfect for delicate work, and a much higher wattage iron for soldering to heavy terminals, lugs and other items that seem to suck up the heat.

I use to modify my old irons by using an external dimmer control, but now its built into this iron.Good quality tip also.

Click Here to see more reviews about: Variable Wattage Soldering Iron 0-50 Watts

Product Description:
Suitable for many applications, this versatile soldering iron is continuously variable from 0 to 50 watts.Length:8".

Buy Now

4/13/2010

Review of Weller 7250N Replacement Soldering Gun Tip

This Weller tip is getting very hard to find locally.Amazon was only place I could find it.Perfect fit.Works great.

Click Here to see more reviews about: Weller 7250N Replacement Soldering Gun Tip

Product Description:
No. 7135W: Fits model No. 8200 gun, 2 per card No. 7250W: Fits model No. D550 gun, 2 per card No. 7235: Fits model No. 7200 Series, 1 per card No. 7135N: Tip with hex nut, 1 per card No. 7250N: Tip with hex nut for old style model No. D550

Buy Now

4/12/2010

Review of Xacto X75170 X-tra Hands with Magnifier

I've started in on a project that requires a lot of small soldering work on circuit boards. My hands aren't very steady so I have difficulty with such small work. Added to that the tiny tiny color bands and markings on components were giving me a head ache trying to decifer them with my unaided eye. This gizmo seemed like the perfect solution to my challenges.

It definately does a great job of holding small components steady for soldering and the adjustability of the arm positions works well. My only complaint is that the magnification is very low. Myabe 2X at best I think. Fortunately my vision just needed a very small boost to help identify the parts without getting eye strain so it works o.k. for me. If you can't see small stuff at all to start with this product may not provide enough magnification to help.

Overall the construction seems to be sturdy and as noted by others the base is good and heavy for its size.

Click Here to see more reviews about: Xacto X75170 X-tra Hands with Magnifier

Product Description:

The X-TRA Hands dual alligator clamps with 2X magnifying glass by X-ACTO is the perfect solution for any hobbyist or designer who needs a second set of hands to hold onto materials. These clamps will hold your work firmly in position, freeing your hands up for soldering, gluing and other tasks.

The powerful, 2X magnifying glass will help you visualize even the smallest areas of your work. These convenient alligator clamps are great for the following tasks:

Gluing in small or tight spaces
Precision "micro" cutting and trimming
Small detail touches
And more

These sturdy alligator clamps attach securely to almost any rigid surface, allowing you to continue working at your desk or workshop without needing to relocate.

X-ACTO office tools and supplies are crafted with the same quality and attention to detail as the legendary X-ACTO knife. Our commitment to quality and performance assures that an X-ACTO product will stand up to the toughest jobs for as long as you need them.

X-ACTO quality office tools and supplies are crafted to achieve the perfect balance between performance and durability. Versatile enough to tackle the most heavy duty jobs and precision tasks at the same time, X-ACTO office tools make getting the job done easier. Additionally, all our products are designed with added attention to your comfort and safety.



Buy Now

4/11/2010

Review of Super Solder Wire 60% 1.0mm Diameter - 1lb Spool

The new "LEAD FREE SOLDER" basically bites.You cannot effectively use it on (new) motherboards.It either rolls right off where you want the solder to adhere, or it takes way too much heat and time to heat to a melting point.So, thank the good Lord that some folks still stock regular ("LEADED")solder!I will definitely be buying more regular solder that isn't "lead free."I got mine from the folks listed here, but you can get it a lot of places on the internet.If you goto your local hardware store and/or even Wallyworld, they may or may not know how to help you out.I find it best to utilize the internet for finding out where to buy stuff online, or who might keep it on the shelves in town.

I can deal with a label or even a stamp warning about dangers involving "lead", (that's in the solder) but they are taking it out of solder, and thats making my job a real challenge.The new kind of solder does NOT work well motherboards.You can take that to the bank.My advice to anyone that works in the industry to get the regular "leaded" type of solder--and stock up on it in case it becomes "UNAVAILABLE" to us!

So, stock up on the "old school" solder if you expect to be working on any motherboards and/or other computer devices which might require solder!

Click Here to see more reviews about: Super Solder Wire 60% 1.0mm Diameter - 1lb Spool

Product Description:
High quality solder for electronics and electrical work. 60% tin and 40% lead with flux in the core for a strong, long lasting bond.

Diameter: .031"/1mm. 1 lb. spool.

Buy Now

4/10/2010

Review of Weller RCT Hot Knife Blade For 8200 Soldering Gun

This blade works very well, particularly with the Harbor Freight Chicago Electric 180W, ITEM 4328-0VGA, soldering gun. This gun heats up much more rapidly than the Weller. However, if you are going to use this for more prolonged use than a few isolated rope searings, the Harbor Freight gun may be too powerful.

Click Here to see more reviews about: Weller RCT Hot Knife Blade For 8200 Soldering Gun

Product Description:
Tip for the Weller 8200 Soldering Gun used for cutting rope or nylon sleeving that is used for cable building and other applications.Heated edge allows rope or braided sleeving to be cut without fraying.

Buy Now

4/09/2010

Review of American Terminal AT-31604 60-40 Rosin Core Solder (4 Ounces)

How do you review a consumable? This stuff worked like solder is supposed to work. All of the electrical connections that I have made with it so far have been perfectly satisfactory.

Click Here to see more reviews about: American Terminal AT-31604 60-40 Rosin Core Solder (4 Ounces)

Product Description:
This spool of American Terminal AT-31604 Solder contains 4 ounces of 1/16" solder with a leaded rosin flux core. The 60% tin, 40% lead combination is perfect for jobs like fine electrical soldering which requiring lower melt temperatures.

Buy Now

4/08/2010

Review of Weller BP645MP Battery Powered Soldering Iron with Batteries

Ever heard of Weller Cold Heat Pro Soldering Tool, Model# CHT100?I did, and I bought one (feel free to read my horrible review on the product's page).What a waste.

So I decided to try again and get this.It's a thousand times better, but still not without it's flaws:

Pros:
1) it doesn't get any more portable
2) works MUCH better than ColdHeat or butane cordless irons
3) It uses a traditional tip that actually GETS HOT when turned on... unlike the Cold Heat, which basically sends current THROUGH your work to heat it up.
4) It's mid-range heat doesn't fry your work.And again, by not zapping your work to heat it up, you don't risk damaging or overheating chips, etc. In fact, I find it a PERFECT heat for circuit boarding -- just hot enough to melt the solder but not to damage the boards.
5) It has a heat-resistant, vented cap you can put on directly after use which even locks-out the on switch to prevent accidental activation in a pocket.

Cons:
1) It does take a long time to warm up, even of fresh batteries.Expect to wait 15-20 seconds holding the button waiting for it to warm up.
2) Batteries don't last too long.
3) It's mid-range temperature doesn't do too well on solder that's been heated and cooled a few times.But then, so does my corded iron.

All in all, I still wholeheartedly recommend the Weller BP645MP!!


Click Here to see more reviews about: Weller BP645MP Battery Powered Soldering Iron with Batteries

Product Description:
The battery-powered soldering iron from Weller is perfect for field service repair on small parts and components. It heats up to working temperature in under 15 seconds and the red LED indicates when power is on. The protective safety cap turns off the power when it's placed on the tool. With one set of fresh batteries, this iron will handle over 120 intermittent solder joints. This kit includes iron, tip, three AA batteries, lead-free solder, and tip wrench.

Buy Now

4/07/2010

Review of Blazer SI-100 Excalibur Multi-Purpose Butane Torch and Hot Air Soldering Kit

Not too sure what I was buying...well, it is a great handy product...can be used in the smallest places...

Click Here to see more reviews about: Blazer SI-100 Excalibur Multi-Purpose Butane Torch and Hot Air Soldering Kit

Product Description:
The Excalibur Multi-Purpose Tool Kit combines a soldering iron, micro torch and hot air blower in one tool with a self-igniting system that provides a faster, more reliable startup.Butane refillable, cordless, Anti-Flare and featuring a new easy to use child resistant design.The Complete Kit Ideal for; Electronic system repair, Automotive, Industrial, Woodworking, Lapidary, Optical repair, General maintenance and Professional jobs.The kit includes 5 interchangeable tips 1 Reflector, 1 Hot Air Blower, 1 Hot Knife, 1 3.5mm Chisel Tip and 1 3mm Diagonal tip.Also comes complete with 1 tube of solder so you're ready to work right out of the box (after a quick fill of Butane).Includes a handy impact resistant travelling case for complete mobility, moves easily between work spaces.

Buy Now

4/06/2010

Review of Weller PSI100K Portasol Super-Pro Self-Igniting Cordless Butane Soldering Iron Kit

I liked this portable soldering tool. At first it worked. But after a year or two, it would not ignite, regardless as to how much butane was put into it. Why? I'm not certain. But I do know that I work out of a truck as an electronics technician and the change of seasons probably wrecked havoc on the ignitor. My supervisor has about 6 of these in a junk pile in the stockroom from my other coworkers. My suggestion is to look at the SOLDERPRO 70. This one needs only an external spark or an external flame to ignite.

Click Here to see more reviews about: Weller PSI100K Portasol Super-Pro Self-Igniting Cordless Butane Soldering Iron Kit

Product Description:
Item #: WELPS100K. "The Potasol" Portable Soldering Kit Cordless, refillable butane gas-powered soldering tool kit!
  • Operates up to 2 hours per refill
  • Maximum temperature of 1076oF
  • Kit contains PSI-100 iron, sponge, stand and extra tips packed in a plastic case

Customers also search for: Discount Cordless Refillable Butane Soldering Gun Kit, Buy Cordless Refillable Butane Soldering Gun Kit, Wholesale Cordless Refillable Butane Soldering Gun Kit, 037103060976, ToolWeb, Soldering Irons

Buy Now

4/05/2010

Review of DESOLDERING PUMP

This one works ok, but I found this pump to get clogged with hardened solder easier than other pumps I've used. Maybe mine has a defect or something but it seems that the suction isn't quite what it needs to be to get the solder all the way into the base. Instead it will sometimes get stuck in the rubber tip and after 4 or 5 joints will clog the tip up so the cleaner bar won't go all the way in and you have to take it apart and clean it out to do more.

Click Here to see more reviews about: DESOLDERING PUMP

Product Description:
Fast action, heavy duty desoldering pump. Simply heat up solder joint and push button. Automatic nozzle cleaner. Display packaged. Standard replacement tip #370-031. Length: 8".

Buy Now

4/04/2010

Review of Weller WP35 35w/120v Professional Soldering Iron with 3-Wire Cord

I have used one WP35 for over 40 years, since I was a kid. The only feature that has changed is that it now has a 3-wire AC cord, not 2. It is a "general purpose" soldering pencil with a very unique temperature-controlled tip that has a magnetic shank on the tip. This keeps the tip temperature relatively steady under load.

This model is perfect for soldering wiring, switches, etc. It is *not* the best choice for PCB electronics work because 1) The tip is too large - there is no smaller tip available than 1/16th inch; 2) It delivers too much heat for small electronics components. This fries the tiny parts and unnecessarily cooks the flux. The perfect Weller hobbyist's model for PCB work is the WLC100 that has user-variable temperature and additional 1/32 inch tips.

Pros:
-) Extraordinarily durable.
-) Comfortable to hold for long periods - it's well balanced.

Cons:
-) Does not come with a stand or a sponge, both of which are absolutely necessary if you don't want to go out of your mind. Where do you intend to set down a very hot iron ?
-) The body gets rather hot when left on for more than, say, 20 minutes.
-) The cushy grip will probably disintegrate after 10 to 20 years. (oh well)

I have a discontinued Weller cast iron stand that is also indestructible. Cheaper, lighter plastic stands are readily available. *** The stand's holder opening diametermust be closely matched to the pencil model - don't expect a random model stand to work properly.


Click Here to see more reviews about: Weller WP35 35w/120v Professional Soldering Iron with 3-Wire Cord

Product Description:
Product Features: # Ideal for a wide variety of electronic tasks - has ST3 soldering tip # Uses ST series long life double-coated iron-plated tips # Tip temperature: 850°F # Quick change knurled collar - stainless steel barrel # Light blue with cushion grip handle and plug-in heating element # 6' 3-wire cord - iron is 7 7/8 long # IMPORTANT: Use only Weller® tips # UL and cUL listed (120 VAC units only)

Buy Now

4/03/2010

Review of Weller WPS18MP PRO Series High Performance 60-Watt Soldering Iron

I bought this about a month ago to augment my personal toolkit I use in Iraq.I terminate a lot of radio cables, but need something that's fast to heat up and has a reasonable cool-down because of the random nature of when I need it.

Pros:
Heats up fast, and tells you when it's ready.

Excellent ergonomics.Soldering a pin onto a cable (especially with a 90 degree connector) is a very precise task.The soldering guns we have (TK-101/GSQ component, Weller GT7As) have huge tips not suitable for the work, and holding the trigger is annoying.The shape conforms to your hand well and lets you get it into tight spaces like a 90 degree connector's pin well easily.

Quick-change tip lets me separate the parts effortlessly in my toolbag so the tip sits in a pocket instead of the main area.

Con:
Only real one is personal preference; I don't like using the conical tips.They don't hold the solder well and get degraded faster than chisel tips.Being able to hold a small bead of solder and insert it into the hole in the pin is the ideal method when doing RG58, because holding longer will heat and expand the dielectric.If it came with both tips that would have been great, but not a major concern.

Overall, this is a great tool.

Click Here to see more reviews about: Weller WPS18MP PRO Series High Performance 60-Watt Soldering Iron

Product Description:
Pro Series High Performance Soldering IronType: Soldering IronMaximum Watts: 18

Buy Now

4/02/2010

Review of Mastech 60 Watts Soldering Iron, UL listed

Great price for a 60W iron, cheapest I could find. Does its job well enough, even though it smokes a little sometimes from between the tip and barrel (it did this before I first used solder, so it's really the iron that is smoking, but it's really minimal).

Click Here to see more reviews about: Mastech 60 Watts Soldering Iron, UL listed

Product Description:
This professional 60 watt soldering iron features a replaceable tip, ergonomically designed cool grip rubber handle, and a nickel-iron plated long life copper tip. It provides an operating tip temperature of up to 860°F with fast heating time and quick heating recovery. 120 VAC.

Buy Now

4/01/2010

Review of Weller P2KC Portasol Professional Self-igniting Cordless Butane Soldering Iron Kit

Wow I am impressed. I spent the last three days on the roof of my house putting up ham radio antenna systems. I needed to solder many conections, unsolder them and resolder them as I was triming antenna to resonant length. This tool is really good. I am showing it to everyone who comes in the house. The hot torch tip is useful to unsolder large-wire connections, the type that seems to suck up all the heat of a normal soldering iron. The iron heats up almost instantly, I have never had a failed start when I click the start button. There is a wire fashioned tool holder that I haven't quite figured out how it is supposed to hold something. This is a real tool for real jobs.

Click Here to see more reviews about: Weller P2KC Portasol Professional Self-igniting Cordless Butane Soldering Iron Kit

Product Description:
The new Portasol® cordless soldering tool from Weller® gives you the ultimate in portable power and convenience for all your soldering jobs. Slide the fuel button forward, press the piezo switch, and the tool's super-fast heat-up lets you melt solder in under a minute. The Portasol® cordless soldering tool is powerful too, adjusting from the equivalent of 25 to 75 watts for temperatures up to 850°F. Refueled with standard butane in just 20 seconds, the Portasol® P2C lasts for up to an hour of continuous use. Kit includes tool with five tips (PPT6 3/32" double flat soldering tip, PPT12 flame tip, PPT10 hot knife tip, PPT9 hot air tip, and PPT11 hot air deflector tip), sponge and tray, tool holder, storage case, and instructions. Mfg. #P2KC. Replacement tips available.

Buy Now

3/31/2010

Review of 5 PC SOLDERING GUN W/ CASE - SOLDERING IRON

100 watts for a gun isn't much power.I mainly wanted it to use on my guitars but it doesn't get hot enough to connect the wires to the back of the potentiometers (and yes, the tip was screwed in tight).All three tips are the same and are not very precise.

Very cheap unit.Okay for small wiring but any mass will not heat up enough for solder flow.

Click Here to see more reviews about: 5 PC SOLDERING GUN W/ CASE - SOLDERING IRON

Product Description:
Contains: 2 Extra Cutters, Container of Flux, Tube of Solder/Wire.Includes a Blow Mold Carry Case

Buy Now

3/30/2010

Review of Weller WESD51 Digital Soldering Station with Power Unit, Soldering Pencil, Stand, Sponge

The Weller WESD51 is an excellent low cost soldering iron for the lab technician or hobbyist.The key benefit is the ability to accurately control and monitor the tip temperature.This allows using the lowest possible temperature setting (675° - 725°) which prolongs tip life and prevents component damage.

It can handle a wide range of tasks from very small SMD components to large ground connections.The silicone rubber cord resists high temperatures should the tip accidentally come in contact.I have one on my lab bench at work and liked it so much I bought one for my home workbench.

Click Here to see more reviews about: Weller WESD51 Digital Soldering Station with Power Unit, Soldering Pencil, Stand, Sponge

Product Description:
The Weller WESD51 Digital Soldering Station, with included power unit, soldering pencil, stand, and sponge, is the perfect choice for a variety of soldering applications, including industrial manufacturing, rework, repairs, and more. The comfortable foam-grip pencil and variable digital temperature controls with LCD (liquid-crystal display) give you complete command over the soldering iron for precise results. Plus, with a non-burnable silicone rubber cord, ESD safety for sensitive components, and automatic shut-off technology, the WESD51 is safe enough to use in a continuous production environment.

The WESD51's heater and sensor combination offers quick heat-up times and temperature recovery for highly efficient soldering.View larger.
The Weller WESD51 Digital Soldering Station features:
  • A digital LCD display for easy operation
  • A durable design ideal for industrial manufacturing applications
  • A temperature lock-out feature that prevents excessive temperatures
  • An automatic sleep-mode that turns off soldering station after 99 minutes of inactivity
  • Adjustable temperature controls; quick heat-up and recovery times

Digital Electronic Temperature Control for Better Performance
No matter what your soldering job is, the WESD51's digital electronic control system lets you easily set the temperature you need to get the job done right. The soldering temperature is adjustable from 350 to 850 degrees Fahrenheit and is accurately measured to within nine degrees. Additionally, the temperature can be viewed in either Fahrenheit or Celsius on the LCD (liquid-crystal display). And the WESD51's innovative built-in heater and sensor combination offers quick heat-up times and temperature recovery for better heat control over the course of your job.
The WESD51's wireless temperature lockout prevents you from raising the temperature beyond what is recommended for your workpiece, board, or component. This eliminates the possibility of damaging components by accidentally setting the temperature too high for the job.
Comfortable, Easy-to-Use Soldering Pencil
The kit's PES51 Soldering Pencil features a durable Nichrome-wound stainless steel heating element for long life and quick response time. Stainless steel will not corrode at high temperatures, meaning you can use this durable pencil for a long time to come. An added bonus, the PES51 Soldering Pencil is compatible with Weller ET series tips.
The PES51 also features a non-burning silicone rubber cord, a lightweight handle made from high-impact ESD (electro-static discharge) plastic, and a foam sleeve that allows for continuous use without fatigue or heat discomfort.

Wireless temperature lockout enhances your work's precision.Innovative Features Improve Safety and Durability
The WESD51 Soldering Station meets Weller's high standards of quality and safety. The station will automatically shut off power to the tool after 99 minutes of inactivity, which helps to conserve electricity and extends the life of the tool. The easy-to-read LCD (liquid-crystal display) lets you know what mode the WESD51 is in, and it lets you know what the temperature is. This way, you can easily see if the temperature is locked or unlocked, and whether or not the unit is turned on.
The Weller WESD51 Soldering station is UL/CUL listed, which means that it meets or exceeds independent safety standards. The PES51 Soldering Pencil is designed to be used in electrostatic-free workstations, and, for added safety, it is completely free of stored static charges. The WESD51 Soldering Station is backed by a one-year warranty.
What's in the Box
WESD51PU Power Unit, PES51 Soldering Pencil, PH50 Stand, and sponge.


Buy Now